6.26 doas
@doas[1..].
| Name | Input? | Runtime? | Type | Variability | Description |
|---|---|---|---|---|---|
| name | X | X | string | constant | – |
| supFan.fanTy | X | X | unrecognized | autosize and simulate phase start time | – |
| supFan.vfDs | X | X | number | end of each subhour | Design supply volumetric flow rate of the heat exchanger |
| supFan.vfDs_As | X | X | number | autosize and simulate phase start time | – |
| supFan.vfDs_AsNov | X | X | number | autosize and simulate phase start time | – |
| supFan.vfMxF | X | X | number | autosize and simulate phase start time | – |
| supFan.press | X | X | number | run start time (of each phase, autoSize or simulate) | – |
| supFan.eff | X | X | number | run start time (of each phase, autoSize or simulate) | – |
| supFan.shaftPwr | X | X | number | run start time (of each phase, autoSize or simulate) | – |
| supFan.elecPwr | X | X | number | run start time (of each phase, autoSize or simulate) | – |
| supFan.motTy | X | X | unrecognized | run start time (of each phase, autoSize or simulate) | – |
| supFan.motEff | X | X | number | autosize and simulate phase start time | – |
| supFan.motPos | X | X | unrecognized | autosize and simulate phase start time | – |
| supFan.curvePy.k[0] | X | X | number | autosize and simulate phase start time | – |
| supFan.curvePy.k[1] | X | X | number | autosize and simulate phase start time | – |
| supFan.curvePy.k[2] | X | X | number | autosize and simulate phase start time | – |
| supFan.curvePy.k[3] | X | X | number | autosize and simulate phase start time | – |
| supFan.curvePy.k[4] | X | X | number | autosize and simulate phase start time | – |
| supFan.curvePy.k[5] | X | X | number | autosize and simulate phase start time | – |
| supFan.mtri | X | X | integer number | input time | – |
| supFan.endUse | X | X | integer number | autosize and simulate phase start time | – |
| supFan.ausz | X | X | integer number | run start time (of each phase, autoSize or simulate) | – |
| supFan.outPower | X | X | number | subhourly | – |
| supFan.airPower | X | X | number | subhourly | – |
| supFan.cMx | X | X | number | end of each subhour | – |
| supFan.c | X | X | number | end of each subhour | – |
| supFan.t | X | X | number | end of each subhour | – |
| supFan.frOn | X | X | number | end of each subhour | – |
| supFan.p | X | X | number | end of each subhour | – |
| supFan.q | X | X | number | end of each subhour | – |
| supFan.dT | X | X | number | end of each subhour | – |
| supFan.qAround | X | X | number | end of each subhour | – |
| exhFan.fanTy | X | X | unrecognized | autosize and simulate phase start time | – |
| exhFan.vfDs | X | X | number | end of each subhour | Design supply volumetric flow rate of the heat exchanger |
| exhFan.vfDs_As | X | X | number | autosize and simulate phase start time | – |
| exhFan.vfDs_AsNov | X | X | number | autosize and simulate phase start time | – |
| exhFan.vfMxF | X | X | number | autosize and simulate phase start time | – |
| exhFan.press | X | X | number | run start time (of each phase, autoSize or simulate) | – |
| exhFan.eff | X | X | number | run start time (of each phase, autoSize or simulate) | – |
| exhFan.shaftPwr | X | X | number | run start time (of each phase, autoSize or simulate) | – |
| exhFan.elecPwr | X | X | number | run start time (of each phase, autoSize or simulate) | – |
| exhFan.motTy | X | X | unrecognized | run start time (of each phase, autoSize or simulate) | – |
| exhFan.motEff | X | X | number | autosize and simulate phase start time | – |
| exhFan.motPos | X | X | unrecognized | autosize and simulate phase start time | – |
| exhFan.curvePy.k[0] | X | X | number | autosize and simulate phase start time | – |
| exhFan.curvePy.k[1] | X | X | number | autosize and simulate phase start time | – |
| exhFan.curvePy.k[2] | X | X | number | autosize and simulate phase start time | – |
| exhFan.curvePy.k[3] | X | X | number | autosize and simulate phase start time | – |
| exhFan.curvePy.k[4] | X | X | number | autosize and simulate phase start time | – |
| exhFan.curvePy.k[5] | X | X | number | autosize and simulate phase start time | – |
| exhFan.mtri | X | X | integer number | input time | – |
| exhFan.endUse | X | X | integer number | autosize and simulate phase start time | – |
| exhFan.ausz | X | X | integer number | run start time (of each phase, autoSize or simulate) | – |
| exhFan.outPower | X | X | number | subhourly | – |
| exhFan.airPower | X | X | number | subhourly | – |
| exhFan.cMx | X | X | number | end of each subhour | – |
| exhFan.c | X | X | number | end of each subhour | – |
| exhFan.t | X | X | number | end of each subhour | – |
| exhFan.frOn | X | X | number | end of each subhour | – |
| exhFan.p | X | X | number | end of each subhour | – |
| exhFan.q | X | X | number | end of each subhour | – |
| exhFan.dT | X | X | number | end of each subhour | – |
| exhFan.qAround | X | X | number | end of each subhour | – |
| supTH | X | X | number | subhourly | Supply temperature heating setpoint |
| EIRH | X | X | number | subhourly | Heating coil energy input ratio (1/efficiency (or 1/cop) |
| coilHMtri | X | X | integer number | input time | Meter for heating coil |
| supTC | X | X | number | subhourly | Supply temperature cooling setpoint |
| EIRC | X | X | number | subhourly | Cooling coil energy input ratio (1/efficiency (or 1/cop) |
| SHRtarget | X | X | number | subhourly | Target cooling coil shr. could be overriden by oa_shr. |
| coilCMtri | X | X | integer number | input time | Meter for heating coil |
| loadMtri | X | X | integer number | input time | Loadmtr idx for accumulation of coil output |
| tEx | X | X | number | subhourly | Doas exterior air drybulb temp, f |
| wEx | X | X | number | subhourly | Doas exterior air humidity ratio, lb/lb |
| hx.VfDs | X | X | number | run start time (of each phase, autoSize or simulate) | Design supply volumetric flow rate of the heat exchanger |
| hx.f2 | X | X | number | run start time (of each phase, autoSize or simulate) | Flow fraction for second set of inputs (default 0.75) |
| hx.senEffH[0] | X | X | number | run start time (of each phase, autoSize or simulate) | Heat exchanger heating sensible effectiveness |
| hx.senEffH[1] | X | X | number | run start time (of each phase, autoSize or simulate) | Heat exchanger heating sensible effectiveness |
| hx.latEffH[0] | X | X | number | run start time (of each phase, autoSize or simulate) | Heat exchanger heating latent effectiveness |
| hx.latEffH[1] | X | X | number | run start time (of each phase, autoSize or simulate) | Heat exchanger heating latent effectiveness |
| hx.senEffC[0] | X | X | number | run start time (of each phase, autoSize or simulate) | Heat exchanger cooling sensible effectiveness |
| hx.senEffC[1] | X | X | number | run start time (of each phase, autoSize or simulate) | Heat exchanger cooling sensible effectiveness |
| hx.latEffC[0] | X | X | number | run start time (of each phase, autoSize or simulate) | Heat exchanger cooling latent effectiveness |
| hx.latEffC[1] | X | X | number | run start time (of each phase, autoSize or simulate) | Heat exchanger cooling latent effectiveness |
| hx.bypass | X | X | integer number | run start time (of each phase, autoSize or simulate) | Hx can be bypassed when not adventatgeous |
| hx.auxPwr | X | X | number | subhourly | Auxiliary power, w |
| hx.auxMtri | X | X | integer number | run start time (of each phase, autoSize or simulate) | Meter for auxiliary power |
| hx.supInAF.tdb | X | X | number | end of each subhour | – |
| hx.supInAF.w | X | X | number | end of each subhour | – |
| hx.supInAF.amf | X | X | number | end of each subhour | – |
| hx.hxInAF.tdb | X | X | number | end of each subhour | – |
| hx.hxInAF.w | X | X | number | end of each subhour | – |
| hx.hxInAF.amf | X | X | number | end of each subhour | – |
| hx.hxOutAF.tdb | X | X | number | end of each subhour | – |
| hx.hxOutAF.w | X | X | number | end of each subhour | – |
| hx.hxOutAF.amf | X | X | number | end of each subhour | – |
| hx.bypassAF.tdb | X | X | number | end of each subhour | – |
| hx.bypassAF.w | X | X | number | end of each subhour | – |
| hx.bypassAF.amf | X | X | number | end of each subhour | – |
| hx.exhInAF.tdb | X | X | number | end of each subhour | – |
| hx.exhInAF.w | X | X | number | end of each subhour | – |
| hx.exhInAF.amf | X | X | number | end of each subhour | – |
| hx.supOutAF.tdb | X | X | number | end of each subhour | – |
| hx.supOutAF.w | X | X | number | end of each subhour | – |
| hx.supOutAF.amf | X | X | number | end of each subhour | – |
| hx.bypassFrac | X | X | number | end of each subhour | Fraction of supply inlet air bypassing heat exchanger |
| hx.tSet | X | X | number | end of each subhour | Setpoint temperature for air exiting heat exchanger |
| hx.sensEff | X | X | number | end of each subhour | Sensible efficacy |
| hx.latEff | X | X | number | end of each subhour | Latent efficacy |
| supAF.tdb | X | X | number | end of each subhour | – |
| supAF.w | X | X | number | end of each subhour | – |
| supAF.amf | X | X | number | end of each subhour | – |
| exhAF.tdb | X | X | number | end of each subhour | – |
| exhAF.w | X | X | number | end of each subhour | – |
| exhAF.amf | X | X | number | end of each subhour | – |
| supQSen | X | X | number | end of each subhour | Sensible heat added (+) or removed (-) from the supply for tempering |
| supQLat | X | X | number | end of each subhour | Latent heat added (+) or removed (-) from the supply for tempering |
| SHR | X | X | number | end of each subhour | Actual cooling coil shr. same as oa_shrtarget unless adjusted for humidity limits. |